BLOG

Focus on hot topics, real-time dynamics

Back to Overview

Precautions for freeze-drying blackberries

2026-11-04

Freeze dried blackberries are more difficult to serve than strawberries and apple slices, mainly due to their softness, high sugar and acidity, dense skin, easy collapse, and moisture absorption. In production, the focus should be on cleaning, pre freezing, palletizing, sublimation temperature control, analytical drying, and low humidity packaging.
1. Raw material cleaning should "remove impurities, pesticide residues, and minimize damage"
Choose fresh, evenly sized, mold free, insect free, and non fermented blackberries.
After spraying with flowing salt water, rinse with clean water. The concentration of salt water is usually 0.5% -0.7%, which helps to reduce the risk of surface microorganisms and pesticide residues. thirty-four
After cleaning, try to drain the surface water as much as possible. Excessive surface water can prolong the pre freezing and freeze-drying time, and also easily cause adhesion.
2. Pre freezing must be thorough, and the center temperature must be lowered to the appropriate level
Berries like blackberries are recommended to be frozen at -30 ° C to -40 ° C, with the center temperature lowered to at least -25 ° C.
The pre freezing time is usually 5-10 hours, depending on the thickness of the tray and the capacity of the quick freezing equipment.
Vacuuming before complete freezing can easily lead to foaming, collapse, spraying, and uneven drying.
If conditions permit, the eutectic point/collapse temperature of blackberries can be measured or explored, and the pre freezing temperature should generally be 5-10 ℃ lower than the eutectic point.
3. Install the tray in a single layer and lay it flat, without stacking it too thick
The blackberry fruit has an irregular shape, so try to lay it flat in a single layer when plating to avoid stacking.
Excessive thickness of the material layer can cause uneven drying between the upper and lower layers, with the bottom prone to clogging and the upper layer prone to over drying.
Leave air ducts between the trays, and control the loading amount according to the rated area of the equipment. Blindly increasing the amount is not advisable.
4. The fruit skin is dense, and if necessary, "micro peeling" treatment should be performed
Blackberry, blueberry and other whole berry fruits have denser skin and fewer channels for water sublimation, which can easily lead to internal water vapor not being released, later collapse or prolonged drying time.
Consider:
Slight puncture, needle rolling and skin breakage;
Or use mild splitting and fracturing treatment;
It is also possible to compare the drying speed and finished product morphology of whole fruit, half fruit, and cut fruit through small-scale experiments.
But the skin should not be excessively broken, otherwise the juice will seep out too much, and after freeze-drying, it is prone to clumping and darkening in color.
5. The temperature control during the sublimation stage should be slow to avoid collapse
The vacuum degree is generally controlled between 10-100 Pa, and is commonly around 10-30 Pa for food products.
The shelf temperature should be gradually increased in sections, and should not be pulled to high temperatures at the beginning.
Blackberry contains sugar, and if heated too quickly, the surface is prone to crust formation, making it difficult for internal moisture to escape, resulting in collapse, stickiness, and blackening of color.
It is recommended to keep the temperature of the cold trap at a lower level, usually below -45 ℃ to -55 ℃, which is more stable to ensure effective capture of water vapor.
6. To analyze drying, it is necessary to remove the bound water completely
After sublimation, it enters the analysis and drying stage, and can be heated appropriately. However, blackberries are heat sensitive berries, and the analysis temperature should not be too high.
The common temperature for food analysis is 30-40 ℃, and the final moisture content is generally controlled below 6.5%, which is more conducive to storage.
If the analysis is insufficient, the finished product is prone to moisture regain, stickiness, and mold growth in the later stage; If the analysis is too intense, it is prone to browning and loss of aroma.
7. Pack in low humidity as soon as possible after leaving the warehouse
Freeze dried blackberries have strong hygroscopicity and should be sorted, inspected, and packaged as soon as possible after being released from the warehouse.
The relative humidity of the packaging environment should be low, and it is best to equip a dehumidification or low humidity packaging room.
Commonly used aluminum foil bags and composite bags, combined with nitrogen filling or vacuum packaging, and added with deoxidizer/desiccant.
Finished products should be stored off the ground and walls, kept cool, dry, and away from light.

Contact Us

 

E-mail:

sales@syguanfeng.com

Tel: 
+86 15088506234

 

Address: 

South Industrial Park of Dongguan, Shangyu District, Shaoxing City,Zhejiang Province,China.

 

%E7%AC%AC%E4%B8%80%EF%BC%8C%E6%9C%80%EF%BC%8C%E4%BC%98%E7%A7%80%EF%BC%8C%E5%A2%9E%E5%BC%BA%EF%BC%8C%E4%B8%80%E6%B5%81

Sorry,当前栏目暂无内容!

您可以查看其他栏目或返回 首页

Sorry,The current column has no content!

You can view other columns or return Home

Get

A Quote

Leave us a message and get access to exclusive offers, product updates, and expert advice tailored just for you!

*is requiredl You can ask any questions in the company including products.Please ill in the correct contact infomation so that we can reply to youin time!

Submit
%{tishi_zhanwei}%